PDA

Pogledaj cijelu verziju : Problem sa dizanjem Windows-a..



Maze
13-03-2007, 20:37
Dakle, imam ovakav problem:

Nekada mi se komp boota i po' 15 minuta, a da se ne digne. Onda ga moram restartat, i normalno radi. Koji je tome razlog?
Onda, još jedan problem, nekada kada palim kompjuter, komp mi počne samo pištit:
tit-tit-tit
I nakon restarta, opet radi normalno.
Ako netko nešta zna, recite
I da nisam prčko po žicama. :wink:

flander
13-03-2007, 20:38
to ak ti tak pišti možda ti neka od komponenta ni dobro upiknuta,to se meni desilo sa memorijom,pištalo dok nisam jače turno i onda je delalo,možda te koji program hebe,virus...........just gesing

Valnjes 666
13-03-2007, 20:47
Gle,napiši koliko puta pišti,i kako:

Npr- kratko kratko dugo

ili

dugo dugo kratko

ti signali daju podatak o grešci...

Maze
14-03-2007, 08:16
Dugo-kratko. Tako nekak..

pHo3nyX
14-03-2007, 14:27
Dugo-kratko. Tako nekak..

Dugo kratko?? Ako misliš ono da čim upališ počne brzo pištati, onda ti je memorija ošla ili nije dobro upiknuta.

Valnjes 666
14-03-2007, 17:04
Dugo-kratko. Tako nekak..

bitno mi je koliko puta,najčešće su to 3-4 signala.

daj poslušaj još jednom,jer mi se čini da je moguće grafa ili memorija.

C
15-03-2007, 19:53
Dakle, imam ovakav problem:

Nekada mi se komp boota i po' 15 minuta, a da se ne digne. Onda ga moram restartat, i normalno radi. Koji je tome razlog?
Onda, još jedan problem, nekada kada palim kompjuter, komp mi počne samo pištit:
tit-tit-tit
I nakon restarta, opet radi normalno.
Ako netko nešta zna, recite
I da nisam prčko po žicama. :wink:
Nešto ti nije u redu s nekom od komponenata, jer to pištanje ti pokazuje, koja komponenta nije u redu. Za svaku komponentu je drugačiji ritam pištanja. Moguće je da i nije do hardwarea, jer se meni znalo događati isto tako, kada bi overclockirao CPU, onda memorija ne bi dobro radila i pištao bi svaki drugi ili treći restart (ili kada ga palim tek). Resetirao sam BIOS, i sve OK.
Pa pokušaj i ti resetirati BIOS i memoriju. :wink:

Edit: Resetirao sam si BIOS i memoriju, jer se više nije htjeo pokrenuti...svaki put bi pištao... :boohoo:

-Werewolf2-
16-06-2007, 10:53
Dugo-kratko. Tako nekak..

Dugo kratko?? Ako misliš ono da čim upališ počne brzo pištati, onda ti je memorija ošla ili nije dobro upiknuta.

za memoriju je pistanje bez prestranka dugo kratko ti je neki problem sa hardverrom ili ti nije nesto dobro prikačeno ili ti je nesto crklo

v4MP1r3
16-06-2007, 12:10
gledajte, ja uopce ne bih koristio win skin da nije defaul ono...dosadan, a kada i nadjem skin..ovako

cista preporuka, ostavite one alien-skinove i to ako nemate kantu koja pici 999 na sat i ostavlja prasinu iza sebe ko da je proslo krdo nosoroga.
koristite classic skin, skin sa 95ice i 98ice. lijepo nadjete design maker i sami ga dizajnirate, a ako ste prelijeni, trazite klasicne skinove i garant ce te naci na bilo koju temu. ja npr imam monkey island - blood island temu, i sasvim sam zadovoljan

dobijete ikonice, kursor, desktop, zvukove, dobijete sve ko i na "modernijim" skinovima samo sto je puno puno brze

C
16-06-2007, 15:00
Hmm... :rotfl:
Dešava se... :wink:

Stormcrow
16-06-2007, 15:00
jel neko zna sta je kada pisti 3 puta kratko??? to mi je bilo nedavno, i sada je ok :?

C
16-06-2007, 15:02
Ne bih znao šta je u pitanju, ali je hardware.

str33t6l0w
17-06-2007, 10:35
jel neko zna sta je kada pisti 3 puta kratko??? to mi je bilo nedavno, i sada je ok :?

mislim da je ram... izgleda da nije dobro stavljen u utor...

17-06-2007, 16:24
Beep Code Descriptions
1 short DRAM refresh failure
2 short Parity circuit failure
3 short Base 64K RAM failure
4 short System timer failure
5 short Process failure
6 short Keyboard controller Gate A20 error
7 short Virtual mode exception error
8 short Display memory Read/Write test failure
9 short ROM BIOS checksum failure
10 short CMOS shutdown Read/Write error
11 short Cache Memory error
1 long, 3 short Conventional/Extended memory failure
1 long, 8 short Display/Retrace test failed


Short Beep Long Beep Short Beep Descriptions
3 1 - Flash loader failure
3 2 - Failure in system board component
3 3 - Failure in system board component
3 4 - Memory failure
3 5 - Video failure
0 6 - Flash BIOS update error
- 2 x AST low level diagnostics

Beeps Error Message Description Resolution
1 Refresh Failure The memory refresh circuitry is faulty. Reseat the memory SIMMs. If the system still beeps, replace the memory.
2 Parity Error Parity error in the base memory (the first 64 KB block) of memory. Reseat the memory SIMMs. If the system still beeps, replace the memory.
3 Base 64 KB Memory Failure Memory failure in first 64 KB. Reseat the memory SIMMs. If the system still beeps, replace the memory.
4 Timer Not Operational A memory failure in the first 64 KB of memory, or Timer 1 is not functioning. The motherboard must be replaced.
5 Processor error 8042 - Gate A20 Failure The CPU generated an error. The motherboard must be replaced.
6 8042 - Gate A20 Failure Processor Exception Interrupt Error Cannot switch to protected mode. Try a different keyboard, or replace the keyboard fuse, if the keyboard has one.
7 Processor Exception Interrupt Error The CPU on the CPU Card generated an exception interrupt. The motherboard must be replaced.
8 Display Memory Read/Write Error The system video adapter is either missing or its memory is faulty. This is not a fatal error. There is a memory error on the video adapter. Replace the video adapter, or the RAM on the video adapter.
9 ROM Checksum Error The ROM checksum value does not match the value encoded in WINBIOS. The BIOS ROM chip is bad. The system probably needs a new BIOS ROM chip.
10 CMOS Shutdown Register Read/Write Error The shutdown register for CMOS RAM has failed. The motherboard must be replaced.
11 Cache memory bad - do not enable cache The cache memory test failed. Cache memory is disabled. Do not press Ctrl/Alt/Shift <+> to enable cache memory. The motherboard must be replaced.


Beep Code Descriptions
No Beeps No Power, Loose Card, or Short.
1 Short Beep Normal POST, computer is ok.
2 Short Beep POST error, review screen for error code.
Continuous Beep No Power, Loose Card, or Short.
Repeating Short Beep No Power, Loose Card, or Short.
One Long and one Short Beep Motherboard issue.
One Long and Two short Beeps Video (Mono/CGA Display Circuitry) issue.
One Long and Three Short Beeps. Video (EGA) Display Circuitry.
Three Long Beeps Keyboard / Keyboard card error.
One Beep, Blank or Incorrect Display Video Display Circuitry.


Beep Code Descriptions / What to Check
1-1-1-3 Verify Real Mode.
1-1-2-1 Get CPU type.
1-1-2-3 Initialize system hardware.
1-1-3-1 Initialize chipset registers with initial POST values.
1-1-3-2 Set in POST flag.
1-1-3-3 Initialize CPU registers.
1-1-4-1 Initialize cache to initial POST values.
1-1-4-3 Initialize I/O.
1-2-1-1 Initialize Power Management.
1-2-1-2 Load alternate registers with initial POST values.
1-2-1-3 Jump to UserPatch0.
1-2-2-1 Initialize keyboard controller.
1-2-2-3 BIOS ROM checksum.
1-2-3-1 8254 timer initialization.
1-2-3-3 8237 DMA controller initialization.
1-2-4-1 Reset Programmable Interrupt Controller.
1-3-1-1 Test DRAM refresh.
1-3-1-3 Test 8742 Keyboard Controller.
1-3-2-1 Set ES segment to register to 4 GB.
1-3-3-1 28 Autosize DRAM.
1-3-3-3 Clear 512K base RAM.
1-3-4-1 Test 512 base address lines.
1-3-4-3 Test 512K base memory.
1-4-1-3 Test CPU bus-clock frequency.
1-4-2-4 Reinitialize the chipset.
1-4-3-1 Shadow system BIOS ROM.
1-4-3-2 Reinitialize the cache.
1-4-3-3 Autosize cache.
1-4-4-1 Configure advanced chipset registers.
1-4-4-2 Load alternate registers with CMOS values.
2-1-1-1 Set Initial CPU speed.
2-1-1-3 Initialize interrupt vectors.
2-1-2-1 Initialize BIOS interrupts.
2-1-2-3 Check ROM copyright notice.
2-1-2-4 Initialize manager for PCI Options ROMs.
2-1-3-1 Check video configuration against CMOS.
2-1-3-2 Initialize PCI bus and devices.
2-1-3-3 Initialize all video adapters in system.
2-1-4-1 Shadow video BIOS ROM.
2-1-4-3 Display copyright notice.
2-2-1-1 Display CPU type and speed.
2-2-1-3 Test keyboard.
2-2-2-1 Set key click if enabled.
2-2-2-3 56 Enable keyboard.
2-2-3-1 Test for unexpected interrupts.
2-2-3-3 Display prompt "Press F2 to enter SETUP".
2-2-4-1 Test RAM between 512 and 640k.
2-3-1-1 Test expanded memory.
2-3-1-3 Test extended memory address lines.
2-3-2-1 Jump to UserPatch1.
2-3-2-3 Configure advanced cache registers.
2-3-3-1 Enable external and CPU caches.
2-3-3-3 Display external cache size.
2-3-4-1 Display shadow message.
2-3-4-3 Display non-disposable segments.
2-4-1-1 Display error messages.
2-4-1-3 Check for configuration errors.
2-4-2-1 Test real-time clock.
2-4-2-3 Check for keyboard errors
2-4-4-1 Set up hardware interrupts vectors.
2-4-4-3 Test coprocessor if present.
3-1-1-1 Disable onboard I/O ports.
3-1-1-3 Detect and install external RS232 ports.
3-1-2-1 Detect and install external parallel ports.
3-1-2-3 Re-initialize onboard I/O ports.
3-1-3-1 Initialize BIOS Data Area.
3-1-3-3 Initialize Extended BIOS Data Area.
3-1-4-1 Initialize floppy controller.
3-2-1-1 Initialize hard-disk controller.
3-2-1-2 Initialize local-bus hard-disk controller.
3-2-1-3 Jump to UserPatch2.
3-2-2-1 Disable A20 address line.
3-2-2-3 Clear huge ES segment register.
3-2-3-1 Search for option ROMs.
3-2-3-3 Shadow option ROMs.
3-2-4-1 Set up Power Management.
3-2-4-3 Enable hardware interrupts.
3-3-1-1 Set time of day.
3-3-1-3 Check key lock.
3-3-3-1 Erase F2 prompt.
3-3-3-3 Scan for F2 key stroke.
3-3-4-1 Enter SETUP.
3-3-4-3 Clear in-POST flag.
3-4-1-1 Check for errors
3-4-1-3 POST done--prepare to boot operating system.
3-4-2-1 One beep.
3-4-2-3 Check password (optional).
3-4-3-1 Clear global descriptor table.
3-4-4-1 Clear parity checkers.
3-4-4-3 Clear screen (optional).
3-4-4-4 Check virus and backup reminders.
4-1-1-1 Try to boot with INT 19.
4-2-1-1 Interrupt handler error.
4-2-1-3 Unknown interrupt error.
4-2-2-1 Pending interrupt error.
4-2-2-3 Initialize option ROM error.
4-2-3-1 Shutdown error.
4-2-3-3 Extended Block Move.
4-2-4-1 Shutdown 10 error.
4-3-1-3 Initialize the chipset.
4-3-1-4 Initialize refresh counter.
4-3-2-1 Check for Forced Flash.
4-3-2-2 Check HW status of ROM.
4-3-2-3 BIOS ROM is OK.
4-3-2-4 Do a complete RAM test.
4-3-3-1 Do OEM initialization.
4-3-3-2 Initialize interrupt controller.
4-3-3-3 Read in bootstrap code.
4-3-3-4 Initialize all vectors.
4-3-4-1 Boot the Flash program.
4-3-4-2 Initialize the boot device.
4-3-4-3 Boot code was read OK.


Traži.... :D

D.E.M.O.
17-06-2007, 18:37
imam i ja problem.. znate onaj svijetlo-plavi ekran koji se pojavi pri bootu?.. onaj sto bi trebao searhat errore i ta njasra?.. e on mi dodje na stage 2 (od 3) i tamo se zbloksa na 0%.. otad sam reinstalirao windowse ali nakon par dana.. guess what.. isti problem :|

Shadowhell
17-06-2007, 18:52
sigurno se zbloka? jer meni zna stajati na 0 minutu pa onda krene